NAG FL Interface
c06pwf (fft_​hermitian_​2d)

1 Purpose

c06pwf computes the two-dimensional inverse discrete Fourier transform of a bivariate Hermitian sequence of complex data values.

2 Specification

Fortran Interface
Subroutine c06pwf ( m, n, y, x, ifail)
Integer, Intent (In) :: m, n
Integer, Intent (Inout) :: ifail
Real (Kind=nag_wp), Intent (Out) :: x(m*n)
Complex (Kind=nag_wp), Intent (In) :: y((m/2+1)*n)
C Header Interface
#include <nag.h>
void  c06pwf_ (const Integer *m, const Integer *n, const Complex y[], double x[], Integer *ifail)
The routine may be called by the names c06pwf or nagf_sum_fft_hermitian_2d.

3 Description

c06pwf computes the two-dimensional inverse discrete Fourier transform of a bivariate Hermitian sequence of complex data values zj1j2, for j1=0,1,,m-1 and j2=0,1,,n-1.
The discrete Fourier transform is here defined by
x^ k1 k2 = 1mn j1=0 m-1 j2=0 n-1 z j1 j2 × exp 2πi j1 k1 m + j2 k2 n ,  
where k1=0,1,,m-1 and k2=0,1,,n-1. (Note the scale factor of 1mn in this definition.)
Because the input data satisfies conjugate symmetry (i.e., z j1 j2 is the complex conjugate of z m-j1 n-j2 , the transformed values x^ k1 k2 are real.
A call of c06pvf followed by a call of c06pwf will restore the original data.
This routine calls c06pqf and c06prf to perform multiple one-dimensional discrete Fourier transforms by the fast Fourier transform (FFT) algorithm in Brigham (1974) and Temperton (1983).

4 References

Brigham E O (1974) The Fast Fourier Transform Prentice–Hall
Temperton C (1983) Fast mixed-radix real Fourier transforms J. Comput. Phys. 52 340–350

5 Arguments

1: m Integer Input
On entry: m, the first dimension of the transform.
Constraint: m1.
2: n Integer Input
On entry: n, the second dimension of the transform.
Constraint: n1.
3: y m/2+1×n Complex (Kind=nag_wp) array Input
On entry: the Hermitian sequence of complex input dataset z, where z j1 j2 is stored in y j2 × m/2+1 + j1, for j1=0,1,,m/2 and j2=0,1,,n-1. That is, if y is regarded as a two-dimensional array of dimension 0:m/2,0:n-1 , yj1j2 must contain z j1 j2 .
4: x m×n Real (Kind=nag_wp) array Output
On exit: the real output dataset x^, where x^ k1 k2 is stored in x k2 × m+ k1, for k1=0,1,,m-1 and k2=0,1,,n-1. That is, if x is regarded as a two-dimensional array of dimension 0:m-1,0:n-1 , xk1k2 contains x^ k1 k2 .
5: ifail Integer Input/Output
On entry: ifail must be set to 0, -1 or 1 to set behaviour on detection of an error; these values have no effect when no error is detected.
A value of 0 causes the printing of an error message and program execution will be halted; otherwise program execution continues. A value of -1 means that an error message is printed while a value of 1 means that it is not.
If halting is not appropriate, the value -1 or 1 is recommended. If message printing is undesirable, then the value 1 is recommended. Otherwise, the value 0 is recommended. When the value -1 or 1 is used it is essential to test the value of ifail on exit.
On exit: ifail=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

If on entry ifail=0 or -1, explanatory error messages are output on the current error message unit (as defined by x04aaf).
Errors or warnings detected by the routine:
ifail=1
On entry, m=value.
Constraint: m1.
ifail=2
On entry, n=value.
Constraint: n1.
ifail=3
An internal error has occurred in this routine. Check the routine call and any array sizes. If the call is correct then please contact NAG for assistance.
ifail=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 7 in the Introduction to the NAG Library FL Interface for further information.
ifail=-399
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.
ifail=-999
Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.

7 Accuracy

Some indication of accuracy can be obtained by performing a forward transform using c06pvf and a backward transform using c06pwf, and comparing the results with the original sequence (in exact arithmetic they would be identical).

8 Parallelism and Performance

c06pwf is threaded by NAG for parallel execution in multithreaded implementations of the NAG Library.
c06pwf makes calls to BLAS and/or LAPACK routines, which may be threaded within the vendor library used by this implementation. Consult the documentation for the vendor library for further information.
Please consult the X06 Chapter Introduction for information on how to control and interrogate the OpenMP environment used within this routine. Please also consult the Users' Note for your implementation for any additional implementation-specific information.

9 Further Comments

The time taken by c06pwf is approximately proportional to mn logmn , but also depends on the factors of m and n. c06pwf is fastest if the only prime factors of m and n are 2, 3 and 5, and is particularly slow if m or n is a large prime, or has large prime factors.
Workspace is internally allocated by c06pwf. The total size of these arrays is approximately proportional to mn.

10 Example

See Section 10 in c06pvf.