# NAG FL Interfaces21ccf (jactheta_​real)

## 1Purpose

s21ccf returns the value of one of the Jacobian theta functions ${\theta }_{0}\left(x,q\right)$, ${\theta }_{1}\left(x,q\right)$, ${\theta }_{2}\left(x,q\right)$, ${\theta }_{3}\left(x,q\right)$ or ${\theta }_{4}\left(x,q\right)$ for a real argument $x$ and non-negative $q<1$, via the function name.

## 2Specification

Fortran Interface
 Function s21ccf ( k, x, q,
 Real (Kind=nag_wp) :: s21ccf Integer, Intent (In) :: k Integer, Intent (Inout) :: ifail Real (Kind=nag_wp), Intent (In) :: x, q
#include <nag.h>
 double s21ccf_ (const Integer *k, const double *x, const double *q, Integer *ifail)
The routine may be called by the names s21ccf or nagf_specfun_jactheta_real.

## 3Description

s21ccf evaluates an approximation to the Jacobian theta functions ${\theta }_{0}\left(x,q\right)$, ${\theta }_{1}\left(x,q\right)$, ${\theta }_{2}\left(x,q\right)$, ${\theta }_{3}\left(x,q\right)$ and ${\theta }_{4}\left(x,q\right)$ given by
 $θ0x,q = 1+2∑n=1∞-1nqn2cos2nπx, θ1x,q = 2∑n=0∞-1nq n+12 2sin2n+1πx, θ2x,q = 2∑n=0∞q n+12 2cos2n+1πx, θ3x,q = 1+2∑n=1∞qn2cos2nπx, θ4x,q = θ0x,q,$
where $x$ and $q$ (the nome) are real with $0\le q<1$.
These functions are important in practice because every one of the Jacobian elliptic functions (see s21cbf) can be expressed as the ratio of two Jacobian theta functions (see Whittaker and Watson (1990)). There is also a bewildering variety of notations used in the literature to define them. Some authors (e.g., Section 16.27 of Abramowitz and Stegun (1972)) define the argument in the trigonometric terms to be $x$ instead of $\pi x$. This can often lead to confusion, so great care must therefore be exercised when consulting the literature. Further details (including various relations and identities) can be found in the references.
s21ccf is based on a truncated series approach. If $t$ differs from $x$ or $-x$ by an integer when $0\le t\le \frac{1}{2}$, it follows from the periodicity and symmetry properties of the functions that ${\theta }_{1}\left(x,q\right)=±{\theta }_{1}\left(t,q\right)$ and ${\theta }_{3}\left(x,q\right)=±{\theta }_{3}\left(t,q\right)$. In a region for which the approximation is sufficiently accurate, ${\theta }_{1}$ is set equal to the first term ($n=0$) of the transformed series
 $θ1t,q=2λπe-λt2∑n=0∞-1ne-λ n+12 2sinh2n+1λt$
and ${\theta }_{3}$ is set equal to the first two terms (i.e., $n\le 1$) of
 $θ3t,q=λπe-λt2 1+2∑n=1∞e-λn2cosh2nλt ,$
where $\lambda ={\pi }^{2}/\left|{\mathrm{log}}_{\mathrm{e}}q\right|$. Otherwise, the trigonometric series for ${\theta }_{1}\left(t,q\right)$ and ${\theta }_{3}\left(t,q\right)$ are used. For all values of $x$, ${\theta }_{0}$ and ${\theta }_{2}$ are computed from the relations ${\theta }_{0}\left(x,q\right)={\theta }_{3}\left(\frac{1}{2}-\left|x\right|,q\right)$ and ${\theta }_{2}\left(x,q\right)={\theta }_{1}\left(\frac{1}{2}-\left|x\right|,q\right)$.

## 4References

Abramowitz M and Stegun I A (1972) Handbook of Mathematical Functions (3rd Edition) Dover Publications
Byrd P F and Friedman M D (1971) Handbook of Elliptic Integrals for Engineers and Scientists pp. 315–320 (2nd Edition) Springer–Verlag
Magnus W, Oberhettinger F and Soni R P (1966) Formulas and Theorems for the Special Functions of Mathematical Physics 371–377 Springer–Verlag
Tølke F (1966) Praktische Funktionenlehre (Bd. II) 1–38 Springer–Verlag
Whittaker E T and Watson G N (1990) A Course in Modern Analysis (4th Edition) Cambridge University Press

## 5Arguments

1: $\mathbf{k}$Integer Input
On entry: denotes the function ${\theta }_{k}\left(x,q\right)$ to be evaluated. Note that ${\mathbf{k}}=4$ is equivalent to ${\mathbf{k}}=0$.
Constraint: $0\le {\mathbf{k}}\le 4$.
2: $\mathbf{x}$Real (Kind=nag_wp) Input
On entry: the argument $x$ of the function.
3: $\mathbf{q}$Real (Kind=nag_wp) Input
On entry: the argument $q$ of the function.
Constraint: $0.0\le {\mathbf{q}}<1.0$.
4: $\mathbf{ifail}$Integer Input/Output
On entry: ifail must be set to $0$, . If you are unfamiliar with this argument you should refer to Section 4 in the Introduction to the NAG Library FL Interface for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value is recommended. If the output of error messages is undesirable, then the value $1$ is recommended. Otherwise, if you are not familiar with this argument, the recommended value is $0$. When the value is used it is essential to test the value of ifail on exit.
On exit: ${\mathbf{ifail}}={\mathbf{0}}$ unless the routine detects an error or a warning has been flagged (see Section 6).

## 6Error Indicators and Warnings

If on entry ${\mathbf{ifail}}=0$ or $-1$, explanatory error messages are output on the current error message unit (as defined by x04aaf).
Errors or warnings detected by the routine:
${\mathbf{ifail}}=1$
On entry, ${\mathbf{k}}=〈\mathit{\text{value}}〉$.
Constraint: ${\mathbf{k}}\le 4$.
On entry, ${\mathbf{k}}=〈\mathit{\text{value}}〉$.
Constraint: ${\mathbf{k}}\ge 0$.
On entry, ${\mathbf{q}}=〈\mathit{\text{value}}〉$.
Constraint: ${\mathbf{q}}<1.0$.
On entry, ${\mathbf{q}}=〈\mathit{\text{value}}〉$.
Constraint: ${\mathbf{q}}\ge 0.0$.
${\mathbf{ifail}}=-99$
See Section 7 in the Introduction to the NAG Library FL Interface for further information.
${\mathbf{ifail}}=-399$
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.
${\mathbf{ifail}}=-999$
Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.

## 7Accuracy

In principle the routine is capable of achieving full relative precision in the computed values. However, the accuracy obtainable in practice depends on the accuracy of the standard elementary functions such as sin and cos.

## 8Parallelism and Performance

s21ccf is not threaded in any implementation.

None.

## 10Example

This example evaluates ${\theta }_{2}\left(x,q\right)$ at $x=0.7$ when $q=0.4$, and prints the results.

### 10.1Program Text

Program Text (s21ccfe.f90)

### 10.2Program Data

Program Data (s21ccfe.d)

### 10.3Program Results

Program Results (s21ccfe.r)