NAG CL Interface
s20aqc (fresnel_​s_​vector)

1 Purpose

s20aqc returns an array of values for the Fresnel integral Sx.

2 Specification

#include <nag.h>
void  s20aqc (Integer n, const double x[], double f[], NagError *fail)
The function may be called by the names: s20aqc, nag_specfun_fresnel_s_vector or nag_fresnel_s_vector.

3 Description

s20aqc evaluates an approximation to the Fresnel integral
Sxi=0xisinπ2t2dt  
for an array of arguments xi, for i=1,2,,n.
Note:  Sx=-S-x, so the approximation need only consider x0.0.
The function is based on three Chebyshev expansions:
For 0<x3,
Sx=x3r=0arTrt,   with ​ t=2 x3 4-1.  
For x>3,
Sx=12-fxxcosπ2x2-gxx3sinπ2x2 ,  
where fx=r=0brTrt,
and gx=r=0crTrt,
with t=2 3x 4-1.
For small x, Sx π6x3. This approximation is used when x is sufficiently small for the result to be correct to machine precision. For very small x, this approximation would underflow; the result is then set exactly to zero.
For large x, fx 1π and gx 1π2 . Therefore for moderately large x, when 1π2x3 is negligible compared with 12 , the second term in the approximation for x>3 may be dropped. For very large x, when 1πx becomes negligible, Sx12 . However, there will be considerable difficulties in calculating cos π2x2 accurately before this final limiting value can be used. Since cos π2x2 is periodic, its value is essentially determined by the fractional part of x2. If x2=N+θ where N is an integer and 0θ<1, then cos π2x2 depends on θ and on N modulo 4. By exploiting this fact, it is possible to retain significance in the calculation of cos π2x2 either all the way to the very large x limit, or at least until the integer part of x2 is equal to the maximum integer allowed on the machine.

4 References

NIST Digital Library of Mathematical Functions

5 Arguments

1: n Integer Input
On entry: n, the number of points.
Constraint: n0.
2: x[n] const double Input
On entry: the argument xi of the function, for i=1,2,,n.
3: f[n] double Output
On exit: Sxi, the function values.
4: fail NagError * Input/Output
The NAG error argument (see Section 7 in the Introduction to the NAG Library CL Interface).

6 Error Indicators and Warnings

NE_ALLOC_FAIL
Dynamic memory allocation failed.
See Section 3.1.2 in the Introduction to the NAG Library CL Interface for further information.
NE_BAD_PARAM
On entry, argument value had an illegal value.
NE_INT
On entry, n=value.
Constraint: n0.
NE_INTERNAL_ERROR
An internal error has occurred in this function. Check the function call and any array sizes. If the call is correct then please contact NAG for assistance.
See Section 7.5 in the Introduction to the NAG Library CL Interface for further information.
NE_NO_LICENCE
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library CL Interface for further information.

7 Accuracy

Let δ and ε be the relative errors in the argument and result respectively.
If δ is somewhat larger than the machine precision (i.e., if δ is due to data errors etc.), then ε and δ are approximately related by:
ε x sin π2 x2 Sx δ.  
Figure 1 shows the behaviour of the error amplification factor x sin π2 x2 Sx .
However, if δ is of the same order as the machine precision, then rounding errors could make ε slightly larger than the above relation predicts.
For small x, ε3δ and hence there is only moderate amplification of relative error. Of course for very small x where the correct result would underflow and exact zero is returned, relative error-control is lost.
For moderately large values of x,
ε 2x sin π2 x2 δ  
and the result will be subject to increasingly large amplification of errors. However, the above relation breaks down for large values of x (i.e., when 1x2 is of the order of the machine precision); in this region the relative error in the result is essentially bounded by 2πx .
Hence the effects of error amplification are limited and at worst the relative error loss should not exceed half the possible number of significant figures.
Figure 1
Figure 1

8 Parallelism and Performance

s20aqc is not threaded in any implementation.

9 Further Comments

None.

10 Example

This example reads values of x from a file, evaluates the function at each value of xi and prints the results.

10.1 Program Text

Program Text (s20aqce.c)

10.2 Program Data

Program Data (s20aqce.d)

10.3 Program Results

Program Results (s20aqce.r)