NAG Library Routine Document

f11jrf (complex_herm_precon_ssor_solve)

1
Purpose

f11jrf solves a system of linear equations involving the preconditioning matrix corresponding to SSOR applied to a complex sparse Hermitian matrix, represented in symmetric coordinate storage format.

2
Specification

Fortran Interface
Subroutine f11jrf ( n, nnz, a, irow, icol, rdiag, omega, check, y, x, iwork, ifail)
Integer, Intent (In):: n, nnz, irow(nnz), icol(nnz)
Integer, Intent (Inout):: ifail
Integer, Intent (Out):: iwork(n+1)
Real (Kind=nag_wp), Intent (In):: rdiag(n), omega
Complex (Kind=nag_wp), Intent (In):: a(nnz), y(n)
Complex (Kind=nag_wp), Intent (Out):: x(n)
Character (1), Intent (In):: check
C Header Interface
#include <nagmk26.h>
void  f11jrf_ (const Integer *n, const Integer *nnz, const Complex a[], const Integer irow[], const Integer icol[], const double rdiag[], const double *omega, const char *check, const Complex y[], Complex x[], Integer iwork[], Integer *ifail, const Charlen length_check)

3
Description

f11jrf solves a system of equations
Mx=y  
involving the preconditioning matrix
M=1ω2-ω D+ω L D-1 D+ω LH  
corresponding to symmetric successive-over-relaxation (SSOR) (see Young (1971)) on a linear system Ax=b, where A is a sparse complex Hermitian matrix stored in symmetric coordinate storage (SCS) format (see Section 2.1.2 in the F11 Chapter Introduction).
In the definition of M given above D is the diagonal part of A, L is the strictly lower triangular part of A and ω is a user-defined relaxation parameter. Note that since A is Hermitian the matrix D is necessarily real.

4
References

Young D (1971) Iterative Solution of Large Linear Systems Academic Press, New York

5
Arguments

1:     n – IntegerInput
On entry: n, the order of the matrix A.
Constraint: n1.
2:     nnz – IntegerInput
On entry: the number of nonzero elements in the lower triangular part of the matrix A.
Constraint: 1nnzn×n+1/2.
3:     annz – Complex (Kind=nag_wp) arrayInput
On entry: the nonzero elements in the lower triangular part of the matrix A, ordered by increasing row index, and by increasing column index within each row. Multiple entries for the same row and column indices are not permitted. The routine f11zpf may be used to order the elements in this way.
4:     irownnz – Integer arrayInput
5:     icolnnz – Integer arrayInput
On entry: the row and column indices of the nonzero elements supplied in array a.
Constraints:
irow and icol must satisfy the following constraints (which may be imposed by a call to f11zpf):
  • 1irowin and 1icoliirowi, for i=1,2,,nnz;
  • irowi-1<irowi or irowi-1=irowi and icoli-1<icoli, for i=2,3,,nnz.
6:     rdiagn – Real (Kind=nag_wp) arrayInput
On entry: the elements of the diagonal matrix D-1, where D is the diagonal part of A. Note that since A is Hermitian the elements of D-1 are necessarily real.
7:     omega – Real (Kind=nag_wp)Input
On entry: the relaxation parameter ω.
Constraint: 0.0<omega<2.0.
8:     check – Character(1)Input
On entry: specifies whether or not the input data should be checked.
check='C'
Checks are carried out on the values of n, nnz, irow, icol and omega.
check='N'
None of these checks are carried out.
Constraint: check='C' or 'N'.
9:     yn – Complex (Kind=nag_wp) arrayInput
On entry: the right-hand side vector y.
10:   xn – Complex (Kind=nag_wp) arrayOutput
On exit: the solution vector x.
11:   iworkn+1 – Integer arrayWorkspace
12:   ifail – IntegerInput/Output
On entry: ifail must be set to 0, -1 or 1. If you are unfamiliar with this argument you should refer to Section 3.4 in How to Use the NAG Library and its Documentation for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1 or 1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this argument, the recommended value is 0. When the value -1 or 1 is used it is essential to test the value of ifail on exit.
On exit: ifail=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6
Error Indicators and Warnings

If on entry ifail=0 or -1, explanatory error messages are output on the current error message unit (as defined by x04aaf).
Errors or warnings detected by the routine:
ifail=1
On entry, check=value.
Constraint: check='C' or 'N'.
ifail=2
On entry, n=value.
Constraint: n1.
On entry, nnz=value.
Constraint: nnz1.
On entry, nnz=value and n=value.
Constraint: nnzn×n+1/2.
On entry, omega=value.
Constraint: 0.0<omega<2.0.
ifail=3
On entry, ai is out of order: i=value.
On entry, I=value, icolI=value, irowI=value.
Constraint: 1icoliirowi.
On entry, I=value, irowI=value and n=value.
Constraint: 1irowin.
On entry, the location (irowI,icolI) is a duplicate: I=value.
A nonzero element has been supplied which does not lie in the lower triangular part of A, is out of order, or has duplicate row and column indices. Consider calling f11zpf to reorder and sum or remove duplicates.
ifail=4
The matrix A has no diagonal entry in row value.
ifail=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.9 in How to Use the NAG Library and its Documentation for further information.
ifail=-399
Your licence key may have expired or may not have been installed correctly.
See Section 3.8 in How to Use the NAG Library and its Documentation for further information.
ifail=-999
Dynamic memory allocation failed.
See Section 3.7 in How to Use the NAG Library and its Documentation for further information.

7
Accuracy

The computed solution x is the exact solution of a perturbed system of equations M+δMx=y, where
δMcnεD+ωLD-1D+ωLT,  
cn is a modest linear function of n, and ε is the machine precision.

8
Parallelism and Performance

f11jrf is not threaded in any implementation.

9
Further Comments

9.1
Timing

The time taken for a call to f11jrf is proportional to nnz.

10
Example

This example program solves the preconditioning equation Mx=y for a 9 by 9 sparse complex Hermitian matrix A, given in symmetric coordinate storage (SCS) format.

10.1
Program Text

Program Text (f11jrfe.f90)

10.2
Program Data

Program Data (f11jrfe.d)

10.3
Program Results

Program Results (f11jrfe.r)