M01EBF (PDF version)
M01 Chapter Contents
M01 Chapter Introduction
NAG Library Manual

NAG Library Routine Document

M01EBF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

 Contents

    1  Purpose
    7  Accuracy

1  Purpose

M01EBF rearranges a vector of integer numbers into the order specified by a vector of ranks.

2  Specification

SUBROUTINE M01EBF ( IV, M1, M2, IRANK, IFAIL)
INTEGER  IV(M2), M1, M2, IRANK(M2), IFAIL

3  Description

M01EBF is designed to be used typically in conjunction with the M01D ranking routines. After one of the M01D routines has been called to determine a vector of ranks, M01EBF can be called to rearrange a vector of integer numbers into the rank order. If the vector of ranks has been generated in some other way, then M01ZBF should be called to check its validity before M01EBF is called.

4  References

None.

5  Parameters

1:     IVM2 – INTEGER arrayInput/Output
On entry: elements M1 to M2 of IV must contain integer values to be rearranged.
On exit: these values are rearranged into rank order. For example, if IRANKi=M1, then the initial value of IVi is moved to IVM1.
2:     M1 – INTEGERInput
3:     M2 – INTEGERInput
On entry: M1 and M2 specify the range of the ranks supplied in IRANK and the elements of IV to be rearranged.
Constraint: 0<M1M2.
4:     IRANKM2 – INTEGER arrayInput/Output
On entry: elements M1 to M2 of IRANK must contain a permutation of the integers M1 to M2, which are interpreted as a vector of ranks.
On exit: used as internal workspace prior to being restored and hence is unchanged.
5:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
On entry,M2<1,
orM1<1,
orM1>M2.
IFAIL=2
Elements M1 to M2 of IRANK contain a value outside the range M1 to M2.
IFAIL=3
Elements M1 to M2 of IRANK contain a repeated value.
IFAIL=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.8 in the Essential Introduction for further information.
IFAIL=-399
Your licence key may have expired or may not have been installed correctly.
See Section 3.7 in the Essential Introduction for further information.
IFAIL=-999
Dynamic memory allocation failed.
See Section 3.6 in the Essential Introduction for further information.
If IFAIL=2 or 3, elements M1 to M2 of IRANK do not contain a permutation of the integers M1 to M2. On exit, the contents of IV may be corrupted. To check the validity of IRANK without the risk of corrupting IV, use M01ZBF.

7  Accuracy

Not applicable.

8  Parallelism and Performance

Not applicable.

9  Further Comments

The average time taken by the routine is approximately proportional to n, where n=M2-M1+1.

10  Example

This example reads a matrix of integers and rearranges its rows so that the elements of the kth column are in ascending order. To do this, the program first calls M01DBF to rank the elements of the kth column, and then calls M01EBF to rearrange each column into the order specified by the ranks. The value of k is read from the datafile.

10.1  Program Text

Program Text (m01ebfe.f90)

10.2  Program Data

Program Data (m01ebfe.d)

10.3  Program Results

Program Results (m01ebfe.r)


M01EBF (PDF version)
M01 Chapter Contents
M01 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2015