G01EPF (PDF version)
G01 Chapter Contents
G01 Chapter Introduction
NAG Library Manual

NAG Library Routine Document

G01EPF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

 Contents

    1  Purpose
    7  Accuracy

1  Purpose

G01EPF calculates upper and lower bounds for the significance of a Durbin–Watson statistic.

2  Specification

SUBROUTINE G01EPF ( N, IP, D, PDL, PDU, WORK, IFAIL)
INTEGER  N, IP, IFAIL
REAL (KIND=nag_wp)  D, PDL, PDU, WORK(N)

3  Description

Let r = r1,r2,,rnT  be the residuals from a linear regression of y on p independent variables, including the mean, where the y values y1,y2,,yn can be considered as a time series. The Durbin–Watson test (see Durbin and Watson (1950), Durbin and Watson (1951) and Durbin and Watson (1971)) can be used to test for serial correlation in the error term in the regression.
The Durbin–Watson test statistic is:
d=i=1 n-1 ri+1-ri 2 i=1nri2 ,  
which can be written as
d=rTAr rTr ,  
where the n by n matrix A is given by
A= 1 -1 0 : -1 2 -1 : 0 -1 2 : : 0 -1 : : : : : : : : -1 0 0 0 1  
with the nonzero eigenvalues of the matrix A being λj=1-cosπj/n, for j=1,2,,n-1.
Durbin and Watson show that the exact distribution of d depends on the eigenvalues of a matrix HA, where H is the hat matrix of independent variables, i.e., the matrix such that the vector of fitted values, y^, can be written as y^=Hy. However, bounds on the distribution can be obtained, the lower bound being
dl=i=1 n-pλiui2 i=1 n-pui2  
and the upper bound being
du=i= 1 n-pλi- 1+pui2 i= 1 n-pui2 ,  
where ui are independent standard Normal variables.
Two algorithms are used to compute the lower tail (significance level) probabilities, pl and pu, associated with dl and du. If n60 the procedure due to Pan (1964) is used, see Farebrother (1980), otherwise Imhof's method (see Imhof (1961)) is used.
The bounds are for the usual test of positive correlation; if a test of negative correlation is required the value of d should be replaced by 4-d.

4  References

Durbin J and Watson G S (1950) Testing for serial correlation in least squares regression. I Biometrika 37 409–428
Durbin J and Watson G S (1951) Testing for serial correlation in least squares regression. II Biometrika 38 159–178
Durbin J and Watson G S (1971) Testing for serial correlation in least squares regression. III Biometrika 58 1–19
Farebrother R W (1980) Algorithm AS 153. Pan's procedure for the tail probabilities of the Durbin–Watson statistic Appl. Statist. 29 224–227
Imhof J P (1961) Computing the distribution of quadratic forms in Normal variables Biometrika 48 419–426
Newbold P (1988) Statistics for Business and Economics Prentice–Hall
Pan Jie–Jian (1964) Distributions of the noncircular serial correlation coefficients Shuxue Jinzhan 7 328–337

5  Parameters

1:     N – INTEGERInput
On entry: n, the number of observations used in calculating the Durbin–Watson statistic.
Constraint: N>IP.
2:     IP – INTEGERInput
On entry: p, the number of independent variables in the regression model, including the mean.
Constraint: IP1.
3:     D – REAL (KIND=nag_wp)Input
On entry: d, the Durbin–Watson statistic.
Constraint: D0.0.
4:     PDL – REAL (KIND=nag_wp)Output
On exit: lower bound for the significance of the Durbin–Watson statistic, pl.
5:     PDU – REAL (KIND=nag_wp)Output
On exit: upper bound for the significance of the Durbin–Watson statistic, pu.
6:     WORKN – REAL (KIND=nag_wp) arrayWorkspace
7:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
On entry,NIP,
orIP<1.
IFAIL=2
On entry,D<0.0.
IFAIL=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.8 in the Essential Introduction for further information.
IFAIL=-399
Your licence key may have expired or may not have been installed correctly.
See Section 3.7 in the Essential Introduction for further information.
IFAIL=-999
Dynamic memory allocation failed.
See Section 3.6 in the Essential Introduction for further information.

7  Accuracy

On successful exit at least 4 decimal places of accuracy are achieved.

8  Parallelism and Performance

Not applicable.

9  Further Comments

If the exact probabilities are required, then the first n-p eigenvalues of HA can be computed and G01JDF used to compute the required probabilities with C set to 0.0 and D to the Durbin–Watson statistic.

10  Example

The values of n, p and the Durbin–Watson statistic d are input and the bounds for the significance level calculated and printed.

10.1  Program Text

Program Text (g01epfe.f90)

10.2  Program Data

Program Data (g01epfe.d)

10.3  Program Results

Program Results (g01epfe.r)


G01EPF (PDF version)
G01 Chapter Contents
G01 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2015