C06PWF (PDF version)
C06 Chapter Contents
C06 Chapter Introduction
NAG Library Manual

NAG Library Routine Document

C06PWF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

+ Contents

    1  Purpose
    7  Accuracy
    9  Example

1  Purpose

C06PWF computes the two-dimensional inverse discrete Fourier transform of a bivariate Hermitian sequence of complex data values.

2  Specification

SUBROUTINE C06PWF ( M, N, Y, X, IFAIL)
INTEGER  M, N, IFAIL
REAL (KIND=nag_wp)  X(M*N)
COMPLEX (KIND=nag_wp)  Y((M/2+1)*N)

3  Description

C06PWF computes the two-dimensional inverse discrete Fourier transform of a bivariate Hermitian sequence of complex data values zj1j2, for j1=0,1,,m-1 and j2=0,1,,n-1.
The discrete Fourier transform is here defined by
x^ k1 k2 = 1mn j1=0 m-1 j2=0 n-1 z j1 j2 × exp 2πi j1 k1 m + j2 k2 n ,
where k1=0,1,,m-1 and k2=0,1,,n-1. (Note the scale factor of 1mn in this definition.)
Because the input data satisfies conjugate symmetry (i.e., z k1 k2  is the complex conjugate of z m-k1 k2 , the transformed values x^ k1 k2  are real.
A call of C06PVF followed by a call of C06PWF will restore the original data.
This routine calls C06PQF and C06PRF to perform multiple one-dimensional discrete Fourier transforms by the fast Fourier transform (FFT) algorithm in Brigham (1974) and Temperton (1983).

4  References

Brigham E O (1974) The Fast Fourier Transform Prentice–Hall
Temperton C (1983) Fast mixed-radix real Fourier transforms J. Comput. Phys. 52 340–350

5  Parameters

1:     M – INTEGERInput
On entry: m, the first dimension of the transform.
Constraint: M1.
2:     N – INTEGERInput
On entry: n, the second dimension of the transform.
Constraint: N1.
3:     Y( M/2+1×N ) – COMPLEX (KIND=nag_wp) arrayInput
On entry: the Hermitian sequence of complex input dataset z, where z j1 j2  is stored in Y j2 × m/2+1 + j1 +1  , for j1=0,1,,m/2 and j2=0,1,,n-1. That is, if Y is regarded as a two-dimensional array of dimension 0:M/2,0:N-1 , then Yj1j2  must contain z j1 j2 .
4:     X( M×N ) – REAL (KIND=nag_wp) arrayOutput
On exit: the real output dataset x^, where x^ k1 k2  is stored in X k2 × m+ k1 +1 , for k1=0,1,,m-1 and k2=0,1,,n-1. That is, if X is regarded as a two-dimensional array of dimension 0:M-1,0:N-1 , then Xk1k2  contains x^ k1 k2 .
5:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
On entry, M=value.
Constraint: M1.
IFAIL=2
On entry, N=value.
Constraint: N1.
IFAIL=3
An internal error has occurred in this function. Check the function call and any array sizes. If the call is correct then please contact NAG for assistance.
IFAIL=-999
Dynamic memory allocation failed.

7  Accuracy

Some indication of accuracy can be obtained by performing a forward transform using C06PVF and a backward transform using C06PWF, and comparing the results with the original sequence (in exact arithmetic they would be identical).

8  Further Comments

The time taken by C06PWF is approximately proportional to mn logmn , but also depends on the factors of m and n. C06PWF is fastest if the only prime factors of m and n are 2, 3 and 5, and is particularly slow if m or n is a large prime, or has large prime factors.
Workspace is internally allocated by C06PWF. The total size of these arrays is approximately proportional to mn.

9  Example

See Section 9 in C06PVF.

C06PWF (PDF version)
C06 Chapter Contents
C06 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2012