NAG C Library Function Document

nag_sum_fast_gauss (c06sac)

1
Purpose

nag_sum_fast_gauss (c06sac) calculates the multidimensional fast Gauss transform.

2
Specification

#include <nag.h>
#include <nagc06.h>
void  nag_sum_fast_gauss (Integer d, const double srcs[], Integer n, const double trgs[], Integer m, const double q[], Integer *p1, Integer *p2, Integer *k, const double hin[], Integer lhin, double tol, double v[], double term[], NagError *fail)

3
Description

nag_sum_fast_gauss (c06sac) calculates the d-dimensional fast Gauss transform (FGT), G^y, that approximates the discrete Gauss transform (DGT), Gy, evaluated at a set of target points yj, for j=1,2,,md. The DGT is defined as:
Gyj= i=1 n qi e - yj - xi 2 2 / h i 2 , j=1,,m  
where xi, for i=1,2,,nd, are the Gaussian source points, qi, for i=1,2,,n+, are the source weights and hi, for i=1,2,,n+, are the source standard deviations (alternatively source scales or source bandwidths).
This function implements the improved FGT algorithm presented in Raykar and Duraiswami (2005). The algorithm clusters the sources into k distinct clusters and then computes two Taylor series approximations per cluster with p1 and p2 terms respectively. You must provide p1, p2 and k when calling the function. See Section 7 below for a further discussion on accuracy when choosing their values.
The input array hin of this function is designed to allow maximum flexibility in the supply of the standard deviation arguments by reusing, in a cyclic manner, elements of the array when it is less than n elements long. For example, if all Gaussian sources have the same standard deviation then it is only necessary to set lhin to 1 and to provide the value of the standard deviation in hin1; the function will then automatically expand hin to be of length n. For further details please see Section 2.6 in the g01 Chapter Introduction.

4
References

Greengard L and Strain J (1991) The Fast Gauss Transform SIAM J. Sci. Statist. Comput. 12(1) 79–94
Raykar V C and Duraiswami R (2005) Improved Fast Gauss Transform With Variable Source Scales University of Maryland Technical Report CS-TR-4727/UMIACS-TR-2005-34

5
Arguments

1:     d IntegerInput
On entry: d, the number of dimensions.
Constraint: d>0.
2:     srcs[d×n] const doubleInput
Note: the i,jth element of the matrix is stored in srcs[j-1×d+i-1].
On entry: x, the locations of the Gaussian sources.
3:     n IntegerInput
On entry: n, the number of Gaussian sources.
Constraint: n>0.
4:     trgs[d×m] const doubleInput
Note: the i,jth element of the matrix is stored in trgs[j-1×d+i-1].
On entry: y, the locations of the target points at which the FGT will be evaluated.
5:     m IntegerInput
On entry: m, the number of target points.
Constraint: m>0.
6:     q[n] const doubleInput
On entry: q, the weights of the Gaussian sources.
7:     p1 Integer *Input/Output
On entry: p1, the number of terms of the first Taylor series to be evaluated.
On exit: p1 is unchanged.
Constraint: p1>0.
8:     p2 Integer *Input/Output
On entry: p2, the number of terms of the second Taylor series to be evaluated.
On exit: p2 is unchanged.
Constraint: p2>0.
9:     k Integer *Input/Output
On entry: k, the number of clusters into which the source points will be aggregated.
On exit: k is unchanged.
Constraint: 1kn.
10:   hin[lhin] const doubleInput
On entry: h, the standard deviations of the Gaussian sources. If lhin<n, the array will be expanded automatically by repeating hin until it is of length n. See Section 2.6 in the g01 Chapter Introduction for further information.
Constraint: hin[i]>0.0, for i=0,1,,lhin-1.
11:   lhin IntegerInput
On entry: the length of the array hin.
Constraint: 1lhinn.
12:   tol doubleInput
On entry: ε, the desired accuracy of the FGT approximation of the DGT. Determines the radius of the source clusters: the contribution of a source point to the FGT approximation at a target point is disregarded if the source is outside the corresponding cluster radius.
Constraint: tol>0.0.
13:   v[m] doubleOutput
On exit: G^y, the value of the FGT evaluated at y.
14:   term[m] doubleOutput
On exit: term[j-1] contains the absolute value of the final Taylor series term that is largest, relative to the size of the sum of the corresponding series, across all clusters that contribute to the FGT at target point v[j-1].
15:   fail NagError *Input/Output
The NAG error argument (see Section 3.7 in How to Use the NAG Library and its Documentation).

6
Error Indicators and Warnings

NE_ALLOC_FAIL
Dynamic memory allocation failed.
See Section 2.3.1.2 in How to Use the NAG Library and its Documentation for further information.
NE_ARRAY_SIZE
On entry, lhin=value.
Constraint: 1lhinn.
NE_BAD_PARAM
On entry, argument value had an illegal value.
NE_INT
On entry, d=value.
Constraint: d>0.
On entry, m=value.
Constraint: m>0.
On entry, n=value.
Constraint: n>0.
On entry, p1=value.
Constraint: p1>0.
On entry, p2=value.
Constraint: p2>0.
NE_INT_2
On entry, k=value and n=value.
Constraint: 1kn.
NE_INTERNAL_ERROR
An internal error has occurred in this function. Check the function call and any array sizes. If the call is correct then please contact NAG for assistance.
See Section 2.7.6 in How to Use the NAG Library and its Documentation for further information.
NE_NO_LICENCE
Your licence key may have expired or may not have been installed correctly.
See Section 2.7.5 in How to Use the NAG Library and its Documentation for further information.
NE_REAL
On entry, tol=value.
Constraint: tol>0.0.
NE_REAL_ARRAY_INPUT
On entry, hin[value]=value.
Constraint: hin[i]>0.0, for i=0,1,,lhin-1.
NW_TOO_FEW_TERMS
On exit, p1=value, p2=value and k=value.
p1, p2 or k may have been too small to calculate v[m-1] to the required accuracy tol.

7
Accuracy

The function does not currently implement the procedure described in Raykar and Duraiswami (2005) for automatically determining values for p1, p2 and k. Non-zero values must therefore be provided for these parameters when calling the function.
For a given set of source and target points and a specified tolerance, there is an interaction between the number of clusters, k, and the number of Taylor series terms, p1 and p2: if the sources are clustered together in fewer clusters (small k) then more terms will be needed in each cluster's Taylor series (large p1 and p2) to capture the effect of the source points further from the cluster centres. Increasing the number of clusters reduces their individual radii and requires fewer terms in their Taylor series, but increases the number of Taylor series that must be evaluated overall.
If the source and target points are uniformly distributed in a unit hypercube, Raykar and Duraiswami (2005) advise users to select khmax+hmin/2-d. If the points are not uniformly distributed then more clusters than this will be needed to calculate the FGT to within the specified tol without requiring prohibitively large values for p1 and p2.
There is less guidance available for selecting good values for p1 and p2. As the number of Taylor series terms is a major factor on the computation time taken by this function, you are advised to initially try a small number, e.g. 20 or so, and then tune p1 and p2 up or down based on the values returned. Note that p1 and p2 are not required to have identical values.
To aid the selection of values for p1, p2 and k, the function returns in term[j-1] the absolute value of the final Taylor series term that is largest, relative to the size of the sum of the corresponding series, across all clusters that contribute to the FGT at target point j. If this value is larger than the requested tol, the function will additionally return a non-zero fail value and you are advised to re-run the function with larger p1, p2 or k.

8
Parallelism and Performance

nag_sum_fast_gauss (c06sac) is threaded by NAG for parallel execution in multithreaded implementations of the NAG Library.
nag_sum_fast_gauss (c06sac) makes calls to BLAS and/or LAPACK routines, which may be threaded within the vendor library used by this implementation. Consult the documentation for the vendor library for further information.
Please consult the x06 Chapter Introduction for information on how to control and interrogate the OpenMP environment used within this function. Please also consult the Users' Note for your implementation for any additional implementation-specific information.

9
Further Comments

The time complexity of the algorithm implemented by this function is OM+N, versus the OMN time complexity of evaluating the DGT directly.

10
Example

In this example values for x, y, p1, p2, k and ε are read in, G^y calculated and the results displayed.

10.1
Program Text

Program Text (c06sace.c)

10.2
Program Data

Program Data (c06sace.d)

10.3
Program Results

Program Results (c06sace.r)